Magnavox’s Universal Remote is considered one of the most groundbreaking technological achievements. Using Magnavox Universal Remote Control Programming Codes, you can control your television and audio-video devices from a Magnavox remote or any universal remote. There are so many Magnavox universal remote codes on this blog, as well as different ways of programming it.
In today’s world, you can enjoy a variety of devices for entertainment including televisions, cable boxes, DVD players, VCRs, and home theatres. It can be frustrating to switch between each of them because each comes with a different controller. Using a Magnavox universal remote control, you can control everything from a single unit, but first, you will need to program the Magnavox Universal Remote.
Page Contents
You can accomplish this in two ways:
1. Coding Philips Magnavox remotes
2. Method of code search
Step 1: Check the remote for batteries. Turn on the TV.
Step 2: Hold down TV and SEL simultaneously for 3 seconds. A light will appear on the button.
Step 3: Enter the TV’s 3 or 4 digit code, choosing the one that corresponds to the TV’s display from the following table.
Step 4: Press the VOLUME + button to confirm. The TV volume should increase as a result.
Step 5: Tap the TV button to store the 3, 4, or 5 digit codes. A blinking signal will confirm the code was stored.
Your remote control is now set up for your entertainment system. Turning it off and on, changing the channel, or changing the volume will allow you to test it.
See Also: Why Are My Headphones Not Working On Windows 10? Simple Solution
Autosearching (code search)
List of Codes for the Magnetavox remote control
1053
1056
1057
1059
1060
1061
1083
1004
1007
1018
1047
2002
2018
2089
2241
2245
2293
2318
2320
2321
2327
32459
1372
1414
1329
1358
3153
3183
3190
3206
3211
3016
3036
3051
3061
3128
3152
A code may work on several devices, while another may be specific to another. You can also search for more Magnavox remote codes for your specific device if the above does not work.
The universal remote codes are scanned in the remote during the auto search method. A code is scanned one at a time to find out which remote code is correct to use to program the control. Follow the directions below:
1. “Turn on” the device you wish to control with the universal remote.
2. Tap the OK/SEL button for 3 seconds while “turning on” the remote. The LED light turns on.
3. Click “CH+” & “CH-” on the remote.
4. Signals will appear on/off. Keep pressing the “up” or “down” key until the device turns off.
5. Click the “power” key to verify the code. Start the device.
6. Make sure the remote is programmed correctly by changing the channel if it starts.
7. Save the code by tapping “device.”. Once this is done, the LED on the device will blink twice.
Our keycodes can be used to program universal remotes easily, and they identify the make and model of your equipment.
1. The device must be turned on first
2. Use the Magnavox universal remote control to select “TV”.
3. When the “Light Flash” appears on the Universal Remote, hold the “Setup button” until it demonstrates that it is in “Learning mode”.
4. Last, enter the “Keycode” from the instruction booklet (programming guide)
5. Having completed the above procedure, you should now be able to press and hold the power button on your remote while pointing at your TV.
6. Whenever the screen turns off, release the “Power Button”
Once you finish this simple process, the universal remote control will work perfectly with your television. If your device doesn’t work, repeat the same procedure with a different code from the same section of the reference table.
Final Thoughts
Do you have too many remote controls? Let Magnavox replace them.
You can program it to work with your TV, cable box, DVD player, and VCR, as well as your audio system. The above guide will guide you in programming your Magnavox universal remote.
